ReaperST
Epic Member
Seems simple enough. Now to find an Uno as wellYep, got a cheap Arduino uno and some jumper cables from DIY to flash the boot loader.
Sent from my SM-G965F using Tapatalk
Seems simple enough. Now to find an Uno as wellYep, got a cheap Arduino uno and some jumper cables from DIY to flash the boot loader.
Seems simple enough. Now to find an Uno as well
Sent from my SM-G965F using Tapatalk
Rather post a sales thread as to make use of thr template etc. It will also attract more potential buyers as thread than it will as a post in a discussion.
Sent from my SM-G965F using Tapatalk
So anybody got one I can borrow?Its just a one time thing to flash the bootloader - After that it is never required again
Just checked my print going now. Can see how that happened quite easily.FYI - Guys getting the Ender 3, print yourself a filament guide. I had under extrusion and after quite a bit of investigations, I realized the guide for the extruder had slightly worn out [emoji24]
I have ordered the full metal one but in the meantime I've super glued the hole shut and added a nut to the front you see below.
View attachment 54952
FYI - Guys getting the Ender 3, print yourself a filament guide. I had under extrusion and after quite a bit of investigations, I realized the guide for the extruder had slightly worn out 😭
I have ordered the full metal one but in the meantime I've super glued the hole shut and added a nut to the front you see below.
Solves that filament rubbing against the z rod too. But how sturdy would that be? Compared to injection moulded part or aluminum?
The cover that came on the z-rod, just cut a short 3cm piece off and slide it down the rod - Now the filament will turn the rubber instead of rubbing against the rod.Solves that filament rubbing against the z rod too. But how sturdy would that be? Compared to injection moulded part or aluminum?
Sent from my SM-G965F using Tapatalk
Knew I should of kept that.... plan is to move the spool next to the printer. Future plansThe cover that came on the z-rod, just cut a short 3cm piece off and slide it down the rod - Now the filament will turn the rubber instead of rubbing against the rod.
I will try the normal mount and report back but my entire hotend and part cooling assembly is made of printed parts and they are sturdy as hell!
But won't you still run into issues when the Z gets higher? As then it will have to pull the filament up (against gravity lol)Knew I should of kept that.... plan is to move the spool next to the printer. Future plans
Sent from my SM-G965F using Tapatalk
Is possible. One way to find outBut won't you still run into issues when the Z gets higher? As then it will have to pull the filament up (against gravity lol)
FYI - Guys getting the Ender 3, print yourself a filament guide. I had under extrusion and after quite a bit of investigations, I realized the guide for the extruder had slightly worn out 😭
I have ordered the full metal one but in the meantime I've super glued the hole shut and added a nut to the front you see below.
Mine too I see
O boy...did not even notice that 🙈🙈
Where you getting the 608 bearings from?I am busy printing these two guides:
Ender 3 Filament Guide by robathome
Ender-3 Bearing Filament Guide by klingler
Both of which will have 608 bearings which should never have this shitty issue again
My print from above just finished - I really wish I could automate the glass bed removal and replacement remotely, even if it was just once...I am busy printing these two guides:
Ender 3 Filament Guide by robathome
Ender-3 Bearing Filament Guide by klingler
Both of which will have 608 bearings which should never have this shitty issue again
3dprintingstore - Like R10 each and they around the corner from my houseWhere you getting the 608 bearings from?
Sent from my SM-G965F using Tapatalk
That's awesome. Looks like another reason to buy more stuff... hahaha3dprintingstore - Like R10 each and they around the corner from my house
I am busy printing these two guides:
Ender 3 Filament Guide by robathome
Ender-3 Bearing Filament Guide by klingler
Both of which will have 608 bearings which should never have this shitty issue again
Stop buying up all the Wanhao filament. Lol.3dprintingstore - Like R10 each and they around the corner from my house
Problem is that they close at 16:30... So I go there once a week to pick up the sweet sweet wanhaoStop buying up all the Wanhao filament. Lol.
Sent from my POCOPHONE F1 using Tapatalk
What do you mean with bugs out?Awesome, 17 hour print with 10% to go and it bugs out. It looks like it was trying to print a slinky at the end.
What do you mean with bugs out?